Huizhou Tianyi rare material Co., Ltd

Product classification
  Sputtering Target
  Rare Earth Material
  Evaporation Material
  Chemical Reagent
  High Pure Metals
  Compounds
About TYR
Aluminum

Aluminum, Al

Aluminum Metal, Al     Aluminum-Scandium alloy, Al-Sc    Aluminum Alloy,    Aluminum Oxide, Al2O3      Aluminum Fluoride, AlF3         Aluminum Nitride, AlN
Aluminum Selenide, Al2Se3    Aluminum Telluride, Al2Te3    Aluminum Nickelide, Al3Ni

Powder   Sputtering Targets    Vacuum Evaporation Material are available

Powder:-625mesh, -325mesh,-200mesh,-160mesth, -100mesh e.t.c particle size
Sputtering Targets : Diameter: 355.6mm (14") max. Single piece Size: Length: <254mm, Width: <127mm, Thickness: >1mm, if larger size than this, we can do it as Tiles joint by 45 degree or 90 degree
Evaporation Material:Pieces: 1-4mm, 1-6mm, 3-6mm, 3-12mm e.t.c,  Tablets: 8-9mm dia. X 4-5mm thick, 10mm dia. X 10mm thick e.t.c

 

Applications:
Aluminum is the most widely used non-ferrous metal
Aluminum is almost always alloyed, which markedly improves its mechanical properties, especially when tempered
Aluminum is usually alloyed – it is used as pure metal only when corrosion resistance and/or workability is more important than strength or hardness. A thin layer of aluminum can be deposited onto a flat surface by physical vapor deposition or (very infrequently) chemical vapor deposition or other chemical means to form optical coatings and mirrors.
Super purity aluminum (SPA, 99.980% to 99.999% Al), used in electronics and CDs.

 

Aluminum Metal, Al     Material Safety Data Sheet(MSDS)for Aluminum, Al


CAS# 7429-90-5, Atomic Weight: 26.9815386, Melting Point: 660.37 oC , Boiling Point:  2519 oC , Density: 2.69890g/cm3. Evaporation Techniques:BN, Glassy coated graphite crucibles , Tungsten Boat, Tungsten coil

Aluminum Metal, Al

99.99%, 99.999%

Chunks, Lump, Granules, Wires, Rods, Disk, Plate, Sheet, Tube, Foil e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 50gram/1 piece

 

Aluminum Oxide, Al2O3   Material Safety Data Sheet(MSDS)for Aluminum Oxide, Al2O3


CAS# 1344-28-1, Atomic Weight:    , Melting Point: 2043 oC , Density: 3.97g/cm3. Evaporation Techniques:Tungsten Boat

Aluminum Oxide, Al2O3

99.99%, 99.999%, ceramic grade

Powders, Chunks, Lump, Granules, Rods, Disk, Plate, Sheet, Tube, Foil, Crucibles  e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 50gram/1 piece

Aluminum Oxide, Al2O3

99.99%, clear, single-crystal

Pieces, granules e.t.c application in Thin Film Coating, vacuum evaporation

M.O.Q: 50gram

Aluminum Oxide doped

Al2O3-ZnO, Al2O3-Sc2O3, Al2O3-TiO2, Al2O3-ZrO2 e.t.c, 99.99%

Chunks, Granules, Lump, Granules, Rods, Disk, Plate, Sheet, Tube, Foil, Crucibles  e.t.c application in Thin Film Coating, Sputtering Targets

 

 

Aluminum-Scandium alloy, Al-Sc   Material Safety Data Sheet(MSDS)for Aluminum-Scandium alloy, Al-Sc


The main application of metallic scandium by weight is in aluminum-scandium alloys for minor aerospace industry components. These alloys contain between 0.1% and 0.5% (by weight) of scandium. Some items of sports equipment, which rely on high performance materials, have been made with scandium-aluminum alloys, including baseball bats , lacrosse sticks, as well as bicycle  frames and components, and tent poles

Aluminum Scandium Alloy, Al-Sc

99.99%, doped Sc=2, 4, 6, 8, 10, 20wt%

Ingot, Chunks, Lump, Granules, Rods, Disk, Plate, Sheet, e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 1 kg/1 piece

 

Aluminum, Alloy


Aluminium alloys are alloys in which aluminum (Al) is the predominant metal. The typical alloying elements are copper, magnesium, manganese, silicon and zinc. There are two principal classifications, namely casting alloys and wrought alloys, both of which are further subdivided into the categories heat-treatable and non-heat-treatable. About 85% of aluminum is used for wrought products, for example rolled plate, foils and extrusions. Cast aluminum alloys yield cost-effective products due to the low melting point, although they generally have lower tensile strengths than wrought alloys. The most important cast aluminum alloy system is Al–Si, where the high levels of silicon (4.0–13%) contribute to give good casting characteristics. Aluminum alloys are widely used in engineering structures and components where light weight or corrosion resistance is required

Al-Si Alloy

99.99%, 99.999%

Granules, Rods, Disk, Plate, Sheet, e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 0.5kg/1 piece

Al-Si-Cu Alloy

99.999%

Granules, Rods, Disk, Plate, Sheet, e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 0.5kg/1 piece

Al-Ti Alloy

99.9%

Granules, Rods, Disk, Plate, Sheet, e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 0.5kg/1 piece

Al-Cu Alloy

99.99%, 99.999%

Granules, Rods, Disk, Plate, Sheet, e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 0.5kg/1 piece

Al-Cr Alloy

99.9%

Granules, Rods, Disk, Plate, Sheet, e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 0.5kg/1 piece

Al-Y Alloy

99.9%

Granules, Rods, Disk, Plate, Sheet, e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 0.5kg/1 piece

Al-Ni Alloy

99.9%

Granules, Rods, Disk, Plate, Sheet, e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 0.5kg/1 piece

Al-Ta Alloy

99.9%

Granules, Rods, Disk, Plate, Sheet, e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 0.5kg/1 piece

Al-W Alloy

99.9%

Granules, Rods, Disk, Plate, Sheet, e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 0.5kg/1 piece

Al-Mo Alloy

99.9%

Granules, Rods, Disk, Plate, Sheet, e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 0.5kg/1 piece

 

Aluminum Fluoride, AlF3       Material Safety Data Sheet(MSDS)for Aluminum Fluoride, AlF3 


CAS# 7784-18-1, Molar mass: 83.9767, white, crystalline solid Odorless powder, Melting Point:1291oC , Density: 3.07g/cm3. Evaporation Techniques: graphite crucibles , Tungsten and Molybdenum Boat

Aluminum Fluoride, AlF3

99.5%~99.99%,

Granules, Pieces Disk, Plate, Sheet e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 50gram/1 piece

 

Aluminum Nitride, AlN         Material Safety Data Sheet(MSDS)for Aluminum Nitride, AlN   


CAS# 24304-00-5, Molar mass: 40.9882g/mol, Melting Point: 2200oC , Boiling Point: 2517oC,  Density: 3.26g/cm3.  white to pale-yellow solid

Aluminum Nitride, AlN

99.9%

Granules, Pieces Disk, Plate, Sheet e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 50gram/1 piece

 

Aluminum Selenide, Al2Se3         Material Safety Data Sheet(MSDS)for Aluminum Selenide, Al2Se3


CAS# 1302-82-5, Molar mass: 290.84g/mol, Melting Point: 960oC , Density: 3.437g/cm3. yellow to brown powder,Monoclinic, mS20, Space group 

Aluminum Selenide

99.9%~99.99%, Al2Se3

Powders, Granules, Pieces Disk, Plate, Sheet e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 50gram/1 piece

 

Aluminum Telluride, Al2Te3      Material Safety Data Sheet(MSDS)for Aluminum Telluride, Al2Te3


CAS# 12042-29-7, Molar mass: 436.7721g/mol,  Melting Point: 900oC, Density: 4.5g/cm3, Al/Te=26.98153868/127.603at= 12.3550/87.645wt %, grey-black powder

Aluminum Telluride

99.9%~99.99%, Al2Te3

Powders, Granules, Pieces Disk, Plate, Sheet e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 50gram/1 piece

 

Aluminum Nickelide, Al3Ni      Material Safety Data Sheet(MSDS)for Aluminum Nickelide, Al3Ni


CAS# 12004-71-6, Molar mass: 139.65g/mol,  Melting Point:    oC, Density:  g/cm3,  

Aluminum Nickelide, Al3Ni

99.9%

Powders, Granules, Pieces Disk, Plate, Sheet e.t.c application in Thin Film Coating, Sputtering Targets

M.O.Q: 50gram/1 piece

Product classification

Huizhou Tianyi rare material Co., Ltd | 粤ICP备案10095113号 | powered by:www.300.cn